Machinery and equipment which have precise tolerances for alignment, or require uniform support, cannot be placed directly onto finished concrete surfaces. Both the concrete surface and the machine base have irregularities which result in alignment difficulties and bearing load concentrations. Cementitious and epoxy grouts are used to fill the void between machine bases and the foundation. These structural grouts take on the role of transferring load between the machine and the foundation.
MYK Grouts can be used to fill the voids between a given substrate (usually concrete) and machinery base-plates, equipment base-plates, anchor bolt holes, bearing-plates, prefabricated columns, rails, and tilt-up panels. Grout can also be injected into surface cracks, or used for waterproofing or repair work.
The performance of a grout under a machine or equipment base depends on the properties of the grout in both the plastic and hardened states. The properties of primary importance are volume change, strength, placement ability, stiffness, and durability.
Properties of the Grouts
Cementitious Grouts: Most cementitious grouts have properties in both the plastic and hardened states which make them acceptable for most applications. They are suitable for transfer of large static compressive loads and for transfer of many dynamic and impact loads.
Epoxy Grouts: Generally, epoxy grouts are used where special requirements such as chemical resistance, high early strength, or impact resistance are needed. When epoxy grouts are subjected to high temperatures their properties may be significantly altered.
|
| Our Range of Grouts & Anchors are as follows |
MYK Grout M40 - Free Flow Non- Shrink cementitious grout for the base plate grouting and especially for sustained loads. MYK Grout M40 possess an ultimate strength of 40 N/mm2 in 28 days.
|
 |
|
|
| TDS |
Brochure |
Case Studies |
|
|
|
MYK Grout M50 - Free Flow Non- Shrink cementitious grout for the base plate grouting especially for sustained loads and for lesser dynamic loads. MYK Grout M50 possess an ultimate strength of min. 50 N/mm2 in 28 days.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
| |
|
|
MYK Grout M65 - Free Flow Non- Shrink cementitious grout for the machine foundation and TG Groutings. Possess high strength to resists both Static and Dynamic loads. MYK Grout M65 possess an ultimate strength of min. 65 N/mm2 in 28 days. Provides an excellent EBA for the Machines.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
|
MYK Grout M80 - Free Flow Non- Shrink cementitious grout with high strengths and early strength achievement. Possess high strength to resists both Static and Dynamic loads. MYK Grout M80 possess an ultimate strength of min. 80 N/mm2 in 28 days.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
| |
|
|
MYK Grout EP750 - Free Flow Epoxy grout with high strengths especially used for the sensitive machineries and were high loadings are anticipated. Possess a very high initial strength, good chemical resistance etc.,
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
|
MYK Grout EP760 LE - Free flow Epoxy grout with high strengths and Low Exothermic properties for mass Grouting, and is specially manufactured to control the cracks due to the heat liberation.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
| |
|
|
MYK Grout ADD - Shrinkage compensating grout additive for the cementitious injection grouting.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
|
MYK Grout Inject E200 - Low viscous epoxy grout for the structural strength enhancements. Especially used to strengthen the old structures and for repairs.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
| |
|
|
MYK Anchor HF66 - Polyester resin anchoring grouts for reinstatement of the steel. Provides an excellent anchoring properties to the concrete or rock in which the steel is to be embedded.
|
|
|
|
| TDS |
Brochure |
Case Studies |
|
|
|
|
|
| |
|
© 2009 all rights reserved.
